Available

Compressor Sizing Calculator

Pressure ratio, discharge temperature and estimated compression power for a defined gas model.

DisciplineMECHANICAL DESIGN
Resource typeCalculation Workbook
Skill levelIntermediate
LanguageEnglish

About this resource

Compressor calculations depend on the thermodynamic model and the pressure basis. This workbook makes both explicit: the gas model, the flow basis, absolute versus gauge pressure and the efficiency definition are stated inputs, not assumptions hidden in a formula.

Flow is converted and, where the required inputs are available, converted to mass flow. The sheet reports the compression pressure ratio, the estimated discharge temperature and the theoretical compression power for the selected model, then applies the stated efficiency to estimate shaft/input power.

The workbook does not select a compressor model or replace a manufacturer performance-map evaluation. Surge analysis, mechanical design and multistage optimisation stay outside its scope.

It is intended for preliminary process and mechanical engineering work on defined, single-stage or explicitly supported compression cases.

What is included

  • Compressor Sizing Calculator workbook — XLSX · Calculator with live formulas, worked example, assumptions and licence sheets. · Editable
  • PDF user guide — PDF · Three-page guide: inputs, method and equations, worked example, units and limits. · Not editable
  • Gas-flow unit conversion
  • Absolute pressure conversion and a stated pressure basis
  • Compression pressure ratio
  • Gas mass-flow calculation where the required inputs are available
  • Estimated discharge temperature using the selected thermodynamic model
  • Theoretical compression power
  • Estimated shaft/input power using stated efficiency inputs

Software compatibility

  • Microsoft Excel: Excel 2016 or later, desktop or Microsoft 365 · required · edit · format based expectation — Formulas use standard worksheet functions only. The workbook was recalculated and checked before release; desktop Excel behaviour is a format-based expectation.
  • LibreOffice Calc: 7.6 or later · optional · edit · format based expectation — Formulas use standard worksheet functions only. The workbook was recalculated and checked before release; desktop Excel behaviour is a format-based expectation.

Prerequisites and technical context

Intended audience

Working engineer, Early-career engineer, Engineering team, Engineering student

Prerequisites

  • Gas flow rate and flow basis (actual, standard or normal)
  • Suction and discharge pressures with a clear absolute or gauge basis
  • Suction temperature
  • Gas molecular weight or specific gas constant
  • Selected compression model and efficiency

Unit systems

  • SI: m³/h, bar(a), °C, kg/kmol, kW
  • Standard and normal flow reference conditions stated explicitly

Assumptions

  • Ideal-gas behaviour unless a compressibility factor is supplied
  • Isentropic or polytropic model selected explicitly
  • Constant specific heat ratio over the compression range
  • Efficiency definitions stated on the calculation sheet

Technical notes

  • Flow reference conditions are recorded so actual and standard flow cannot be confused.
  • Discharge temperature and power both depend on the selected model; the model is printed with the result.
  • The workbook states that it is not a performance-map or surge analysis.

References

  • No external standards or references listed.

Scope and limitations

Included

  • Gas-flow unit conversion
  • Absolute pressure conversion and a stated pressure basis
  • Compression pressure ratio
  • Gas mass-flow calculation where the required inputs are available
  • Estimated discharge temperature using the selected thermodynamic model
  • Theoretical compression power
  • Estimated shaft/input power using stated efficiency inputs

Not included

  • Automatic compressor manufacturer or model selection
  • Compressor performance-map evaluation
  • Surge analysis, vibration and mechanical design
  • Cooling-system design and detailed multistage optimisation
  • Multiphase and reactive gas systems

Limitations

  • Preliminary gas-compression calculations only.
  • Gas properties must be supplied or obtained from a verified source.
  • Real-gas behaviour requires appropriate compressibility and property data.
  • Final compressor selection and operating limits must be confirmed using manufacturer data and detailed engineering review.

Author and review information

Author / publisher: Curious Engineering

Review status: Author checked

Equations are implemented as transparent worksheet formulas with the unit handling shown on each sheet. The shipped worked example uses the default inputs and can be reproduced by hand.

Review scope: Before release, every checked result was recalculated from the workbook and compared with an independent implementation of the same equations, including the worked example, unit conversions and boundary checks. No independent third-party review was commissioned.

Licence and permitted use

Single-user commercial licence

One named user may use this workbook on any number of their own devices for commercial and educational engineering work. Resale, redistribution, publication, sublicensing and inclusion in a paid course or product are not permitted. Adapted copies remain subject to the same terms.

  • Use on your own projects, including paid client work
  • Use for teaching and internal training
  • Adapt the formulas and layout for your own internal templates
  • Keep a personal or company archive copy for business continuity

Not permitted

  • Reselling, sublicensing or distributing the file
  • Publishing the file on a website, shared drive or marketplace
  • Including the file in a paid course, product or template pack
  • Removing the licence, attribution or version notices
Read licence information

Delivery

Orders are confirmed by email before payment. After payment clears, the workbook and PDF guide are sent as a secure download link together with the licence and a short getting-started note. Usually within one business day.

Questions before you buy

What does the Compressor Sizing Calculator calculate?

It covers Gas-flow unit conversion; Absolute pressure conversion and a stated pressure basis; Compression pressure ratio.

Which software do I need?

Microsoft Excel (Excel 2016 or later, desktop or Microsoft 365). The workbook uses standard worksheet functions.

What files are included?

Compressor Sizing Calculator workbook (XLSX), PDF user guide (PDF).

When should I not use it?

Preliminary gas-compression calculations only. Automatic compressor manufacturer or model selection.

Related resources

  • Pump Sizing & Selection Calculator · $12 — An Excel workbook for preliminary pump duty: flow conversion, static and friction head, Total Dynamic Head, hydraulic power and estimated shaft power.
  • Pipe Flow & Pressure Drop Calculator · $12 — An Excel workbook for steady-state single-phase pipe flow: velocity, Reynolds number, Darcy friction factor, straight-pipe and minor pressure losses.