Pressure Vessel Design Calculator
Cylindrical shell thickness for a defined internal-pressure case and stated design basis.



About this resource
Pressure-equipment calculations are only meaningful when the design basis is written down. This workbook records the pressure, temperature, geometry, material allowable stress, joint efficiency and corrosion allowance, then evaluates the required thickness for the cylindrical shell case it implements.
The result is compared with the entered nominal thickness, and the governing equation reference is shown next to the calculation. Corrosion allowance is reported separately so the contribution is visible rather than buried in a total.
The workbook is deliberately narrow. It does not perform a complete code-compliance assessment, and it does not choose a material or certify a vessel. Exact equation references, applicability limits and the material-data source are stated on the calculation sheet.
It is intended as a preliminary calculation aid for mechanical and pressure-equipment engineers, not as the sole basis for fabrication or statutory approval.
What is included
- Pressure Vessel Design Calculator workbook — XLSX · Calculator with live formulas, worked example, assumptions and licence sheets. · Editable
- PDF user guide — PDF · Three-page guide: inputs, method and equations, worked example, units and limits. · Not editable
- Cylindrical shell thickness for the supported internal-pressure case
- Internal-pressure calculation checks
- Selected head thickness calculations only where implemented and validated
- Corrosion allowance treatment reported separately
- Preliminary required-thickness result
- Comparison against the entered nominal thickness
- Governing equation reference on the calculation sheet
Software compatibility
- Microsoft Excel: Excel 2016 or later, desktop or Microsoft 365 · required · edit · format based expectation — Formulas use standard worksheet functions only. The workbook was recalculated and checked before release; desktop Excel behaviour is a format-based expectation.
- LibreOffice Calc: 7.6 or later · optional · edit · format based expectation — Formulas use standard worksheet functions only. The workbook was recalculated and checked before release; desktop Excel behaviour is a format-based expectation.
Prerequisites and technical context
Intended audience
Working engineer, Early-career engineer, Engineering team, Engineering student
Prerequisites
- Design pressure and design temperature
- Internal diameter and relevant cylindrical geometry
- Material allowable stress at design temperature from an identified source
- Weld joint efficiency and corrosion allowance
Unit systems
- SI: bar, °C, mm, MPa
- Consistent field units where supported by the workbook
Assumptions
- Thin-wall cylindrical shell under internal pressure
- Material allowable stress taken at the stated design temperature
- Weld joint efficiency and corrosion allowance applied as entered
- Equation applicability limits stated on the calculation sheet
Technical notes
- The design basis is recorded in one place: pressure, temperature, geometry, material data and allowances.
- Corrosion allowance is reported as a separate contribution to required thickness.
- The calculation summary names the governing equation; it does not claim complete code compliance.
References
- No external standards or references listed.
Scope and limitations
Included
- Cylindrical shell thickness for the supported internal-pressure case
- Internal-pressure calculation checks
- Selected head thickness calculations only where implemented and validated
- Corrosion allowance treatment reported separately
- Preliminary required-thickness result
- Comparison against the entered nominal thickness
- Governing equation reference on the calculation sheet
Not included
- External pressure, vacuum, nozzle reinforcement, supports, saddles and skirts
- Wind, seismic, fatigue and local-load analysis
- Flange design, gasket selection and bolting
- Automatic material selection or material-property certification
- A complete vessel code-compliance assessment
- Fabrication, inspection, testing and regulatory approval
Limitations
- Internal-pressure calculations for the shell case implemented, unless further modules are explicitly listed.
- Material allowable stress and design coefficients must be verified against the governing standard and design temperature.
- The workbook does not certify a design or approve a vessel for fabrication.
- Results must be reviewed by a qualified engineer before any safety-related use.
Author and review information
Author / publisher: Curious Engineering
Review status: Author checked
Equations are implemented as transparent worksheet formulas with the unit handling shown on each sheet. The shipped worked example uses the default inputs and can be reproduced by hand.
Review scope: Before release, every checked result was recalculated from the workbook and compared with an independent implementation of the same equations, including the worked example, unit conversions and boundary checks. No independent third-party review was commissioned.
Licence and permitted use
Single-user commercial licence
One named user may use this workbook on any number of their own devices for commercial and educational engineering work. Resale, redistribution, publication, sublicensing and inclusion in a paid course or product are not permitted. Adapted copies remain subject to the same terms.
- Use on your own projects, including paid client work
- Use for teaching and internal training
- Adapt the formulas and layout for your own internal templates
- Keep a personal or company archive copy for business continuity
Not permitted
- Reselling, sublicensing or distributing the file
- Publishing the file on a website, shared drive or marketplace
- Including the file in a paid course, product or template pack
- Removing the licence, attribution or version notices
Delivery
Orders are confirmed by email before payment. After payment clears, the workbook and PDF guide are sent as a secure download link together with the licence and a short getting-started note. Usually within one business day.
Questions before you buy
What does the Pressure Vessel Design Calculator calculate?
It covers Cylindrical shell thickness for the supported internal-pressure case; Internal-pressure calculation checks; Selected head thickness calculations only where implemented and validated.
Which software do I need?
Microsoft Excel (Excel 2016 or later, desktop or Microsoft 365). The workbook uses standard worksheet functions.
What files are included?
Pressure Vessel Design Calculator workbook (XLSX), PDF user guide (PDF).
When should I not use it?
Internal-pressure calculations for the shell case implemented, unless further modules are explicitly listed. External pressure, vacuum, nozzle reinforcement, supports, saddles and skirts.
Related resources
- Heat Exchanger Design Workbook · $19 — An Excel workbook for preliminary thermal sizing: hot and cold-side duty, energy balance, LMTD, corrected mean temperature difference and estimated area.
- Compressor Sizing Calculator · $15 — An Excel workbook for preliminary compressor process calculations: pressure ratio, mass flow, discharge temperature, theoretical and estimated shaft power.